Does compressor work Apply Ref. Did buzzer sound on forced operation? Check certainly after forced start. Apply Ref. Exchange and troubleshoot the corresponding sensor.
Is F, R Room defrosting heater normal? Check temp. Page 48 Diagnostics If there is a trouble with self-diagnosis - Error of sensor can be seen on the front display of refrigerator.
If power is impressed to refrigerator first, an failure of sensor is found. The refrigerator will stop working and display blink the region of trouble-occurred sensor repetitively. Remove causes after No slightly comprehending the conditions of interference by door gasket, food etc. When there is no buzzer sound with button input, forced operation or door open, disassemble Panel PCB and check if the buzzer is broken or soldering is defective.
Start Is the connector of CoolSelect Zone inserted correctly in the fridge? Reinsert the connector; troubleshoot a bad contact. Reinsert the connector in the main PCB. When you are exchanging the lamp of freezer, please exchange or troubleshoot it with the power OFF to avoid an electric shock. Please keep in mind you do not get burnt by the excessive heating of an incandescent light bulb.
Exchange or troubleshoot the Is ice ejected? Does ice in the ice tray exist? Do you see Ice Stop on the digital panel? Page Reference For Circuit Diagnostics Reference for circuit diagnostics Wire connector on the cabinet door. Measure the voltage at both terminals of a coil and determine if the relay is working. As shown in table below, measure the resistance between terminals, check load trouble and wire connection error.
Page 58 Reference for circuit diagnostics Check sensors Disconnect the connector from the Main PCB, than measure the resistance of the following sensors. Page 59 Reference for circuit diagnostics Table of temperature sensor according to resistance and voltage conversion. This is a table based on the voltage using the 10kohm-F.
Illustrated Parts Catalog. Please access to our service web site. Previous Page. Next Page. Page 2: Important Safety Notice The manufacturer or dealer cannot be responsible for the interpretation of this information.
Page 3: Table Of Contents Contents 1. Page 4: Introduction 1. Given this independent system, the freezer and the refrigerator are cooled individually as required and are, therefore, more efficient. Page 5: Installation 2. Connect water lines and power cord. Page 6: Nomenclature 3. Page 7: Specifications 4. SAMSUNG will repair or replace any part found to be defective, at our option and at no charge as stipulated herein, with new or reconditioned parts during the limited warranty period specified above.
Page 9: Interior Views And Dimensions 6. Page Mechanical Disassembly 8. Page Refrigerator Disassembly 8 8. Page Evaporator In Freezer M M e e c c h h a a n n i i c c a a l l D D i i s s a a s s s s e e m m b b l l y y Evaporator in Freezer Evaporator is located in the bottom of freezer to produce cold air driven across the evaporator coils.
Page Operation Function 9. Page Digital Panel 9. The numbers shown on the digital display panel stand for the actual compartments temperatures. Although you select Power Freeze or Power Cool, the set temperatures in the freezer and refrigerator are not changed. Only the relay control for a cubed-ice dispensing and the SSR control for the ice chute door are performed electronically. Cool option maintains a set temperature of the refrigerator.
The count will be decreased in every minute. Page 28 Operation Function 2 Preparation of Ice-maker Connect the water line to the water supply valve of refrigerator to supply water. If the back of bucket touches the guide-ice of ice maker, the ice maker will not make ice any more because of a ice full signal. Press Power Freeze and Fridge Temp. Page Circuit Descriptions A short error will be ignored. For Quick Cool, the damper will be close. So, when a glitch or error occurs, it is quickly detected.
These errors are reflected in the form of error codes that show on the display panel. An understanding of what each code stands for would be of help to know what went wrong and what to do next.
You can click here for a detailed list of common error codes in Samsung fridges, what they mean, and how to resolve them. This simple move works with our smartphones , laptops , and maybe now, for your refrigerator. This shut down seems to give allowance for the device to break the loop of conflicting commands, reboot and refresh. To allow enough time for it to settle and refresh, leave your refrigerator off for up to 10 or 15 minutes.
Some experts would even recommend up to 24 hours. By now, the refrigerator most likely would have rebalanced and recalibrated itself. Plug it into the power socket and turn it on. To reset your Samsung refrigerator and get it out of shop mode, press the power freezer and power cool buttons simultaneously, holding it for a while — for about 2 to 5 seconds. Thereafter, release the buttons. The refrigerator would have been reset and the cooling function will resume. To reset your Samsung refrigerator and get it out of demo mode, press the Energy Saver and Freezer buttons at the same time, and hold them for about 10 seconds.
Do keep in mind that this method works only for Samsung refrigerators from and older. For newer Samsung refrigerators, you will need to press Freezer, Energy Save, and Lighting simultaneously. In some cases you will need to press Freezer, Energy Save, and Fridge and hold them simultaneously for about 10 seconds. To reset your Samsung refrigerator control panel, simply press the Power Cool and Power Freeze buttons at the same time, and hold for about 10 seconds until you see the numbers on the display reset.
But what if your control panel is not displaying or the buttons are not working at all? Carry out a general reset by following the steps above. To deactivate the child lock feature on your Samsung refrigerator, simply press and hold the child lock button for a few seconds. In the absence of one depending on the model , follow the steps provided for your model in the product manual.
To reset your control panel display, locate the reset switch at the top of the right door interior side and switch it off and then on again. The unit will reboot and the Samsung logo will appear on the panel. Need expert help? Use the chat box on this page to speak with a verified appliance technician right away. No need for expensive in-home service calls. No appointments. No waiting. At times, the display might blink an error code indicating that there is a communication problem between the refrigerator door and the main control unit.
If it is, simply reconnect. If it is in place, still disconnect it and then reconnect it back. Then plug it in and switch on the refrigerator.
0コメント